EN 13480-5-2002
|
ID： |
E43645BFBD6F40B398AADFAA7F179E34 |
|
文件大小(MB)： |
0.19 |
|
页数： |
34 |
|
文件格式： |
|
|
日期： |
2006-9-21 |
|
购买： |
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
EUROPEAN STANDARD,NORME EUROPéENNE,EUROP腎SCHE NORM,EN 13480-5,May 2002,ICS 23.040.01,English version,Metallic industrial piping - Part 5: Inspection and testing,Tuyauteries industrielles métalliques - Partie 5: Inspection,et contr鬺e,Metallische industrielle Rohrleitungen - Teil 5: Prufüng,This European Standard was approved by CEN on 23 May 2002.,CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European,Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national,standards may be obtained on application to the Management Centre or to any CEN member.,This European Standard exists in three official versions (English, French, German). A version in any other language made by translation,under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official,versions.,CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.,EUROPEAN COMMITTEE FOR STANDARDIZATION,COMITé EUROPéEN DE NORMALISATION,EUROP腎SCHES KOMITEE FüR NORMUNG,Management Centre: rue de Stassart, 36 B-1050 Brussels,. 2002 CEN All rights of exploitation in any form and by any means reserved,worldwide for CEN national Members.,Ref. No. EN 13480-5:2002 E,Licensed Copy: sheffieldun sheffieldun, na, Thu Sep 21 06:58:47 BST 2006, Uncontrolled Copy, (c) BSI,EN 13480-5:2002 (E),Issue 1 (2002-05),2,Contents,Foreword4,1 Scope .5,2 Normative references ..5,3 Terms and definitions..6,4 Symbols and abbreviations ..6,5 Determination of inspection and testing requirements ..6,5.1 General..6,5.2 Classification of piping ..6,5.3 Testing and inspection procedures .7,6 Design validation 7,6.1 Objective and extent.7,6.2 Documentation.7,6.2.1 General..7,6.2.2 Design calculations ..7,6.2.3 Technical schedule8,6.3 Performance of design review9,6.3.1 System design review .9,6.3.2 Review of design calculations9,6.3.3 Incomplete documentation 9,6.3.4 Additional procedures/qualifications .9,6.4 Alternative proof of safety .9,6.5 Manufacturer’s declaration of design compliance..10,7 In-process inspection and testing .10,7.1 General10,7.2 Materials and formed pressure retaining parts .10,7.2.1 General10,7.2.2 Verification of material .10,7.2.3 Verification of formed pressure retaining parts 10,7.2.4 Non-destructive testing of formed parts 10,7.2.5 Destructive testing of formed parts ..11,7.3 Welding ..11,7.3.1 Welding approvals ..11,7.3.2 Inspection of welding set-up .12,7.3.3 Testing and inspection during welding ..12,7.3.4 Inspection after welding..12,7.4 Heat treatment12,8 Non-destructive testing of welds 13,8.1 Application of NDT..13,8.1.1 General13,8.1.2 Examination of weld quality by sample inspection.14,8.1.3 Imperfections revealed by sample inspection 14,8.2 Circumferential butt, branch, fillet and seal welds..16,8.2.1 Amount of examination .16,8.2.2 Dissimilar metal joints..18,8.3 Longitudinal welds .18,8.4 NDT Methods..18,8.4.1 General18,8.4.2 Acceptance criteria.18,8.4.3 Personnel qualification .21,Licensed Copy: sheffieldun sheffieldun, na, Thu Sep 21 06:58:47 BST 2006, Uncontrolled Copy, (c) BSI,EN 13480-5:2002 (E),Issue 1 (2002-05),3,8.4.4 Selection of NDT method .22,8.5 Reports ..22,8.6 Weld repairs 22,9 Final assessment and documentation..23,9.1 General23,9.2 Final inspection.23,9.2.1 General23,9.2.2 Visual inspection before the proof test ..23,9.2.3 Visual inspection after the proof test ..23,9.2.4 Review of the manufacturing documents .24,9.3 Proof test ..24,9.3.1 General24,9.3.2 Hydrostatic pressure test 24,9.3.3 Pneumatic pressure test ..27,9.3.4 Other tests 28,9.3.5 Documentation of the proof test .28,9.4 Inspection of safety systems.28,9.5 Documentation..28,9.5.1 Final documentation package ..28,9.5.2 Design and manufacturing documentation package.30,9.5.3 Operating instructions .30,9.5.4 Documentation for the purchaser ..30,10 Declaration/Certification ..30,Annex A (informative) Inspection of safety systems .31,Annex ZA (informative) Clauses of this European Standard addressing essential requirements or,other provisions of EU directives. .32,Licensed Copy: sheffieldun sheffieldun, na, Thu Sep 21 06:58:47 BST 2006, Uncontrolled Copy, (c) BSI,EN 13480-5:2002 (E),Issue 1 (2002-05),4,Foreword,This document (EN 13480-5:2002) has been prepared by Technical Committee CEN/TC 267 "Industrial piping and,pipelines", the secretariat ……
……